Aaaaaaand Totallyyyy Redeemed myself….

Yes.

Yes, that was a modified Dumb and Dumber quote.

Those who know me well, accept the fact that in the warm-weather months I speak fluent Dumb and Dumber (which seasonally transitions mid-November to fluent Elf). It just is.

Anyways, The-Table-Refinishing-That-Never-Ends is finally complete!. And I’m so excited about it that I’m going to ruin the suspense and start with a little “After” glimpse…

IMG_6784

Table. You complete me. (I know… I’m a traitor.  That one was Jerry McGuire.  Seriously, only about 10% of the words I speak are original.)

Anyhoo, not gonna lie… I definitely burned off all of the cookie-calories I consumed while stress-eating over this thing throughout the dual-refinishing process, and it was worth EVERY SECOND. I’ve learned so stinkin’ much throughout this process, and finally have a result I’m satisfied with.

So, let’s start with a quick recap for any newbies. I purchased these drool-worthy mid-century tables for a steal at Goodwill.

20140604-091627-33387486.jpg

The problem was that their finishes had seen better days.

Happily, I was able to salvage the original finish on the smallest table by using mayonnaise to remove water rings. That guy now lives in our tri-functional room….

 IMG_6296

I began work on the coffee table (which is still not finished), but ended up switching gears to the larger end table. I stripped the table with chemical stripper, then stained and finished the table with a water-based poly… which ended up being a HUGE mistake resulting in bubbles and brush strokes galore (and a pathetic-ugly-crying-Christina).

So, it was onto attempt número dos. After my cries for advice were answered by several sweet folks, I came to terms with the fact that I would have to re-strip the table. Check out the comments from my previous two posts for the specific advice given.

I will say that stripping the table went SO much quicker the second time around. My guess is that this is due to a combination of knowing what to expect and using a toothbrush to get the gunk out of all the smaller spaces and crevices (this was a fantastic tip (among many others) given by Beck with Beckwith’s Treasures and was a total time-saver compared with the techniques I used the first time). It worked fabulously well. I also noted that the water-based poly came off in much more solid pieces which made the job slightly less messy…

IMG_6766

Once the table was fully stripped, I decided to use Formby’s Tung Oil.

IMG_6774

This was a product recommended by several awesome folks (including Beck), so I figured I’d give it a go. After a short deliberation, I decided to apply the Tung Oil sans stain to bring out the natural tones of the wood… Problem??? I don’t think I properly prepped the top of the table… My fear of over-stripping the wood (being that this was my second go-around) had prevented me from removing all the film. With the first coat of Tung oil, the top looked mottled and ashy. NOT the look I was going for. And I realized that I should’ve stained the table first. I just really liked that look so much better. I didn’t take a picture of this part as my frustration got the best of me.  Thus, grabbing my camera slipped my mind.  But, take my advice… Do a good job stripping the first (‘er, second) time. You won’t regret it.

At this point, I went inside, ate another cookie, repeated the mantra “At least I only have to strip the top. At least I only have to strip the top…” then decided to risk sanding the top of the table. I say “risk” because of the thin veneer that I was so scared to sand through. I didn’t want to use the stripper again because my understanding was that tung oil penetrates the wood so I figured that if I wanted an evenly stained top, I’d need to sand.  I very, very carefully sanded with 220 grit sandpaper on my orbital sander. And I DID IT. I sanded just enough to allow the stain to evenly penetrate but before I went through the veneer.

Next, I applied a coat of Varathane’s Early American stain. As I’ve said in previous posts, my goal was to stay close to the original look of the table and I’ve found that this particular stain lends that perfect “mid-century” wood tone that the table had before…

IMG_6778

The wood took the stain much more readily this go-around, which resulted in a slightly darker finish than before, but I’m okay with that. It looks rich and luscious while still boasting a mid-century flair. If the table were a person, he’d totally be swinging his flowing locks back and forth in slow motion as Hungry Eyes plays softly in the background.

That night (after about 8 hours of dry time for the stain), I took my labor of love inside. And while catching up on an episode of The Big Bang Theory, I applied the first coat of Formby’s. I simply rubbed in a thin layer with a lint-free cloth and let it dry. It looked somewhat uneven, but I’d read that this was often the case with the first few coats as the wood can sometimes absorb the oil at different rates.   The next day, I gently buffed with fine grit steel wool as recommended…

IMG_6779

…cleaned with tack cloth, and applied a second coat.  I repeated this process again on the entire table, then two more times on just the top and drawer until I had an even finish all over. I still think the the base could use one last coat, just to add a tad of extra gloss, so I may still do that.  But I guess that’s the beauty of this stuff.   You can add layers to enhance as needed.  Applying the tung oil was a process because of the long dry time (12 hours between coats per the instructions), but really it was easy and quick to apply aside from that. And totally worth it.   I wish I had known about this stuff the first time around.

In any case, now my table is now glossy and done (please excuse the weird lighting in these pics… I think I chose an interesting time of day to shoot them)….

IMG_6798

IMG_6787

And check out the top!!  The damaged spot is a smidge darker than the rest of the top, but that’s the only difference. It feels smooth as can be….

IMG_6793

Amazing to me, especially being that the top started off here….

IMG_6697

Remember how I questioned whether I’d even be able to stain the table because the damage went so deeply into the wood??

IMG_6696

The fact that I was able to salvage that inlaid detailing on the top makes me absolutely over the moon.

I was thinking of selling the table once I was finished, but after all the work I put in, this little guy feels like part of the family. I’m THAT attached. So, I’m gonna hang onto him and let him live in our totally mis-matched, not nearly decorated No Man’s Land for a while until I figure out a permanent space for him.

IMG_6808

And I must name him.  For some reason he feels like an “Earl”.  Maybe we’ll just go with that.

I still need to finish the coffee table. So, there’s that. But I have to say that I feel so much more equipped to do that now. As hard as it was in the “during” part, DIY is an adventure yielding many rewards if ya stick through it. I mean, just check out all this knowledge I’ve acquired…

1.  How to strip wood properly (and the consequences if you don’t)

2. How much I hate water-based poly

3. How to apply tung oil and the differences in finish between the various topcoats

4.  My undying love for mid-century pieces and the lengths I will go to  to stay true to them (but I already knew that)

5. How many cookies it takes for me to survive refinishing a table twice within a short period of time (twelve).

Nice, right???   So, on that Hallmark note, I end this post.

What DIY adventures have y’all taken on where you nearly (but didn’t) throw in the towel?

Linked up at: Tatertots & Jello

TDC Before and After

I stripped! *furniture*

Remember my Goodwill mid-century tables that I discussed in this post?  Well, progress has been made (cue applause).

20140604-091627-33387486.jpg

After my sad cry for help as to what to do with these small furniture gods, I took the generous advice given and purchased an orbital sander.   We literally just chose a mid-range sander at Lowe’s and ran with it.

I started with the coffee table… Now, as I’d expressed before, I was very, VERY nervous about sanding through the thin wood veneer on top, so I used 220 grit sandpaper and sanded very slowly…

It took a good hour or so, but (wait for it) I succeeded in getting down to the bare wood without destroying the veneer (joy)

Once I’d finished, I examined my work closely and broke into celebratory dance, respirator and all (it was a fist-pumping-Hammer-dance-combo).  And our neighbor saw me.  I panicked and nearly blurted out something about “table dancing!”, but fortunately, my brain caught up in time to stop that little nugget of awesomesauce from escaping.  Instead, I went with the always-smooth, ever-popular “Um… Hi. (awkward pause) …How’s it goin’?”

Right.  Way to get down with my socially-awkward bad self.  Welcome to my life.

Anyways, my original plan was to use Polyshades because I never-in-a-million-years thought that I’d actually get down to bare wood that could be stained with REAL STAIN.  But I did.  So, it was on.

Next, I proceeded to hand-sand the base of the table.  Which took FOR-ever. I literally got one of the short sides done and decided that I’d go the chemical stripper route .

I’d never used chemical stripper before, so it was a little scary for me.  I was wholly afraid I’d do it wrong and be scarred for life.   But, then I did it anyways.

This is the stripper I went with (it claims to be low odor = Bonus)…

IMG_6698

I decided that since I’d already partially sanded the coffee table, I’d start with chemically stripping the end table because I wanted to see the difference between using the stripper and sanding.  I also wanted to be sure that I was making the right decision by switching methods mid-job on the coffee table.  As a reminder, here’s how the end table looked when I bought it (um, forgot to take a shot of the whole thing (mybad), but here’s the top)…

 IMG_6697

The main issue was this part of the finish…

IMG_5967

I hoped that stripping the table would allow me to be able to refinish it with stain (fingers crossed!).  The damage seemed to go deep into the wood, so I wasn’t sure if I’d be able to pull it off, but figured it was worth a shot (…I told you… I’m a pathetic sappy when it comes to vintage finds #gottadoit).

I started by brushing on the stripper…

IMG_6700

I waited about 2 hours (the directions said you could scrape in as little as 30 minutes or as long as 24 hours).

And I scraped…

IMG_6703

And scraped and scraped, but found that scraping the rounded areas and details was somewhat difficult.

IMG_6705

And although the directions stated that the stripper remains wet for up to 24 hours, my guess is that these statements were not made in the Texas heat.   Granted, I chose to do this during the polar vortex when it was 85 degrees (In July!  In Texas??!), under the shade of the garage.   But the areas facing the driveway still became gummy and difficult to scrape in that time frame.

So, I switched to the second method recommended on the bottle.  Abrasive pad plus mineral spirits…

IMG_6707

IMG_6708

This did the job, but took quite a bit of time and elbow grease.  And murdered a few innocent bystanders…

IMG_6710

And these were the heavy-duty gloves, folks!  TIP: Buy more gloves than you think you need.

I used toothpicks for the little grooves…

IMG_6712

And then (ahem!) a few days later, I gave the table one last scrub down with the mineral spirits.

There were areas where the stripper dried in the crevices…

But I found that simply wiping on a little more stripper was enough to moisten the residue…

…so that it could be scraped out using a very small, pointy screwdriver.

The top of the table looked pretty good at this point, but felt wavy to the touch where that large damaged area was. So, I took the orbital sander with 220 grit sandpaper to it.

I got the top pretty smooth, but not perfect since I was afraid of sanding through the wood veneer.

I lightly hand-sanded the base of the table with more 220 grit in areas where I felt there was still residue. And then went over it again with mineral spirits.   By this point, I had pretty much come to terms with the fact that stripping furniture is a time-consuming task no matter how you slice it.   It’s definitely doable, though.  And I was happy to see that I’d likely be able to stain the table after all my hard work. With that said…

Ladies and gentlemen, if you’re bashful I implore you to avert your eyes….  I give you naked furniture…

(applause! applause!) 

I will say that the damaged spot is still mildly detectable (although it’s hard to see in the pictures)…

The texture is different from the rest of the top and the wood is slightly darker, but all-in-all it’s a vast improvement.   I’m just curious if it’ll absorb the stain differently than the rest of the top.   I guess I’ll just have to do it to find out.

I still have to finish stripping the coffee table, but decided to fully finish this little end table first to be sure it comes out well once stained.  Since I want the two tables to match, if staining the end table doesn’t work out, I’ll paint it, thus there’s no point in wasting time stripping the coffee table if this is the case.  So, I’ll update ya’ll once that’s done.

So anyways, that’s my story… Have ya’ll ever stripped furniture?  Any stories to tell??  Tips??

 

Linked up at: Houseologie, Brepurposed, Anything & Everything, Home Stories A to Z, Lines Across, Sugar Bee Crafts, Home Coming, Tatertots & Jello

The DIY Dreamer
TDC Before and After